Any Ping

Any Ping enable a user to test the reach-ability of a host with many options.

Any Ping is a light weight application to test the reach-ability of a host. Any Ping has many option to advanced ping.

Fetaures:-

1) No root access require.

2) Ping by host name or host IP.

3) Complete output as like terminal.

4) Fast and easy to use.

5) Host history saves automatically.

6) Ability to write option with host(eg: -c 5 host).

7) Many options to execute with command.

Options to ping:-

-c count

Stop after sending count ECHO_REQUEST packets. With deadline

option, ping waits for count ECHO_REPLY packets, until the time-

out expires.

-i interval

Wait interval seconds between sending each packet. The default

is to wait for one second between each packet normally, or not

to wait in flood mode. Only super-user may set interval to val-

ues less 0.2 seconds.

-I interface

interface is either an address, or an interface name. If inter-

face is an address, it sets source address to specified inter-

face address. If interface in an interface name, it sets source

interface to specified interface. For IPv6, when doing ping to

a link-local scope address, link specification (by the '%'-nota-

tion in destination, or by this option) is required.

-l preload

If preload is specified, ping sends that many packets not wait-

ing for reply. Only the super-user may select preload more than

3.

-m mark

use mark to tag the packets going out. This is useful for vari-

ety of reasons within the kernel such as using policy routing to

select specific outbound processing.

-M pmtudisc_opt

Select Path MTU Discovery strategy. pmtudisc_option may be

either do (prohibit fragmentation, even local one), want (do

PMTU discovery, fragment locally when packet size is large), or

dont (do not set DF flag).

-p pattern

You may specify up to 16 ``pad'' bytes to fill out the packet

you send. This is useful for diagnosing data-dependent problems

in a network. For example, -p ff will cause the sent packet to

be filled with all ones.

-Q tos Set Quality of Service -related bits in ICMP datagrams. tos can

be decimal (ping only) or hex number.

In RFC2474, these fields are interpreted as 8-bit Differentiated

Services (DS), consisting of: bits 0-1 (2 lowest bits) of sepa-

rate data, and bits 2-7 (highest 6 bits) of Differentiated Ser-

vices Codepoint (DSCP). In RFC2481 and RFC3168, bits 0-1 are

used for ECN.

Historically (RFC1349, obsoleted by RFC2474), these were inter-

preted as: bit 0 (lowest bit) for reserved (currently being

redefined as congestion control), 1-4 for Type of Service and

bits 5-7 (highest bits) for Precedence.

-s packetsize

Specifies the number of data bytes to be sent. The default is

56, which translates into 64 ICMP data bytes when combined with

the 8 bytes of ICMP header data.

-S sndbuf

Set socket sndbuf. If not specified, it is selected to buffer

not more than one packet.

-t ttl ping only. Set the IP Time to Live.

-T timestamp option

Set special IP timestamp options. timestamp option may be

either tsonly (only timestamps), tsandaddr (timestamps and

addresses) or tsprespec host1 [host2 [host3 [host4]]] (timestamp

prespecified hops).

-w deadline

Specify a timeout, in seconds, before ping exits regardless of

how many packets have been sent or received. In this case ping

does not stop after count packet are sent, it waits either for

deadline expire or until count probes are answered or for some

error notification from network.

-W timeout

Time to wait for a response, in seconds. The option affects only

timeout in absence of any responses, otherwise ping waits for

two RTTs.-

hops

Specify through which path the ping should send the packet to destination.